http://www.tenand.com ??e?????e?t1??? shenzhen tenand technology co.,ltd http://www.tenand.com ??e?????e?t1??? shenzhen tenand technology co.,ltd
12-96 ordering information part number package safety standard approval application part number ltv-8141 ltv-8141m ltv-8141s ltv-8141s-ta ltv-8141s-ta1 ltv8141-v ltv8141m-v ltv8141s-v ltv8141sta-v ltv8141sta1-v ltv-8241 ltv-8241m ltv-8241s ltv-8241s-ta ltv-8241s-ta1 ltv-8441 ltv-8441m ltv-8441s ltv-8441s-ta ltv-8441s-ta1 ltv8241-v ltv8241m-v ltv8241s-v ltv8241sta-v ltv8241sta1-v LTV8441-V ltv8441m-v ltv8441s-v ltv8441sta-v ltv8441sta1-v 4-pin dip 4-pin (leads with 0.4" spacing) 4-pin (lead bends for surface mount) 4-pin (tape and reel packaging of type i) 4-pin (tape and reel packaging of type ii) 8-pin dip 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type i) 8-pin (tape and reel packaging of type ii) 16-pin dip 16-pin (leads with 0.4" spacing) 16-pin (lead bends for surface mount) 16-pin (tape and reel packaging of type i) 16-pin (tape and reel packaging of type ii) 4-pin dip 4-pin (leads with 0.4" spacing) 4-pin (lead bends for surface mount) 4-pin (tape and reel packaging of type i) 4-pin (tape and reel packaging of type ii) 8-pin dip 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type i) 8-pin (tape and reel packaging of type ii) 16-pin dip 16-pin (leads with 0.4" spacing) 16-pin (lead bends for surface mount) 16-pin (tape and reel packaging of type i) 16-pin (tape and reel packaging of type ii) ul approved tuv approved csa approved fimko approved nemko approved semko approved demko approved vde approved ltv-8141 ltv-8241 ltv-8441 ltv-8141 ltv-8241 ltv-8441 note: 1.year date code. 2. 2-digit work week. 3. factory code shall be marked (z : taiwan, y : thailand). 4. all dimensions are in millimeters (inches). 5. tolerance is 0.25mm (.010 ) unless otherwise noted. 6. specifications are subject to change without notice.
photocoupler 12-97 electrical/optical characteristics (ta=25 ) parameter symbol min. typ. max. unit conditions input output transfer characteristics forward voltage terminal capacitance collector dark current collector-emitter breakdown voltage emitter-collector breakdown voltage collector current *current transfer ratio collector-emitter saturation voltage isolation resistance floating capacitance cut-off frequency response time (rise) response time (fall) v f c t i ceo bv ceo bv eco i c ctr v ce(sat) r iso c f f c t r t f 35 6 6 600 50 1 1.2 50 0.8 100 0.6 6 60 53 1.4 250 1 75 7,500 1.0 1.0 300 250 v pf a v v ma % v g pf khz s s absolute maximum ratings (ta=25 ) parameter symbol rating unit input output total power dissipation operating temperature storage temperature *1.isolation voltage *2.soldering temperature forward current power dissipation collector-emitter voltage emitter-collector voltage collector current collector power dissipation i f p v ceo v eco i c p c p tot t opr t stg v iso t sol 50 70 35 6 80 150 200 -30~+100 -55~+125 5 260 ma mw v v ma mw mw kv rms *1. ac for 1 minute, r.h. = 40 ~ 60% isolation voltage shall be measured using the following method. (1)short between anode and cathode on the primary side and between collector, emitter and base on the secondary side. (2)the isolation voltage tester with zero-cross circuit shall be used. (3)the waveform of applied volttage shall be a sine wave. *2. for 10 seconds. i f = 20ma v=0, f=1khz v ce =10v i c =0.1ma i e =10 a i f = 1ma v ce =2v i f = 20ma, i c =5ma dc500v, 40~60% r.h. v=0, f=1mhz v ce =5v, i c =2ma r l =100 , -3db v ce =2v, i c =10ma r l =100 *ctr= 100% i c i f
12-98 typical electrical/optical characteristic curves (25 ambient temperature unless otherwise noted)
photocoupler 12-99
|
